4 Premium Driveshaft Universal Joint Front and/or Rear Moog Greasable

Description

Same Day Dispatch – Priority Mail – Tracked and Insured
This offer is for 4 Universal Joints (Front & Rear).
Fits:
Please do not make any assumptions as far as fitment is concerned. You must verify that this part will fit your exact model and specifics by doing the following:
1) See the table below if your model is included. If so, then
2) Go to the compatibility chart of the listing above.  If you can’t see the compatibility chart, then click on “see compatible vehicles” at the top of the listing to display the chart.
3) Locate your vehicle in the chart by year, make, model….etc.
4) The left most column, is the notes column with important details. Any restrictions or specifics for which this part will or will not fit will be included in these notes.
In general, the drive of your vehicle (4WD, AWD, ….etc) needs to be known.  Also how many drive shafts does your vehicle have? On which drive shaft you want to install the U-Joint and where on that shaft (front, rear, at transmission….etc.)
BUICK
1961-2007
CADILLAC
1950-2016
CHEVROLET
1967-2016
CHRYSLER
2007-2009
DODGE
1975-2009
FORD
1968-1993
GMC
1967-2016
HUMMER
2003
ISUZU
1996-2008
JEEP
2003-2006
LINCOLN
1968-1979
MERCURY
1979
OLDSMOBILE
1954-2004
PLYMOUTH
1974-1981
PONTIAC
1956-2002
SAAB
2005-2009
Premium; Greasable
MOOG premium universal joints are machined to meet or exceed original equipment standards. Each u-joint part is precision-ground to the strictest tolerances, with quality control inspections at every step of the manufacturing process.
Features
Bearing cups are cold-formed and case-hardened, then precision-ground to meet or exceed OE standards, for better wear and strength.
Superior quality seals are designed to keep contaminants out and to allow for proper lubrication.
Needle bearings are precision ground for maximum load-carrying capabilities.
Bearing cups utilize a radial design to allow 360° lubricant distribution to all bearing surfaces.
High strength steel crosses are forged to meet or exceed OE specifications and are carburized heat-treated for long life.
Bearing Cap Axis 1 Diameter
1.125 In.
Bearing Cap Axis 2 Diameter
1.125 In.
Bearing Diameter A
1.125 In.
Bearing Diameter B
1.125 In.
Length A
2.557 in.
Length Axis 1
2.557 in.
Length Axis 2
2.557 in.
Length B
2.557 in.
Bearing Cap Axis 1 Diameter
28.5 mm
Bearing Diameter A
28.5 mm
Bearing Cap Axis 2 Diameter
28.6 MM
Bearing Diameter B
28.6 MM
Bearing Cap Type
4 Grooved Round Bearings
U-Joint Identification
4 Grooved Round Bearings
Length A
64.9 mm
Length Axis 1
64.9 mm
Length Axis 2
64.9 mm
Length B
64.9 mm
Length Measurement B
Inside of Groove to Inside of Groove plus thickness of 2 Lock Rings
OE Series
Mechanics 3, Saginaw 44 and American Axle 1344
Length Measurement A
Outside of Groove to Outside of Groove
Lube Fitting Location
Regular Lube Fitting in Cross
Bearing Type A
Round Grooved
Bearing Type B
Round Grooved
Greasable
Yes
Lubricateable
Yes
Alternate/OEM Part Number(s): 10951029, 10952423, 12471502, 12479126, 26042371, 5093377AB, 5093377AC, 68004848, 68004848AB
U-JOINT SPECIFICATIONS
U-Joint Identification
4 Grooved Round Bearings
Bearing Type A
Round Grooved
Bearing Diameter A - Inch
1.125
Bearing Diameter A - mm
28.5
Length Measurement A
Outside of Groove to Outside of Groove
Length A - Inch
2.557
Length A - mm
64.9
Bearing Type B
Round Grooved
Bearing Diameter B - Inch
1.125
Bearing Diameter B - mm
28.6
Length Measurement B
Outside of Groove to Outside of Groove
Length B - Inch
2.557
Length B - mm
64.9
OE Series
Mechanics 3, Saginaw 44 and American Axle 1344
Lubricateable
YES
Lube Fitting Location
Regular Lube Fitting in Cross
Dimension Across Bearing Wing A - Inch
1.69
Dimension Across Bearing Wing A - mm
42.9
Dimension Across U-Joint A - Inch
4.5
Dimension Across U-Joint A - mm
114.3
Bearing Type Notes
Uses Delta Wing Bearings in place of Low Wing Bearings
MOOG/PRECISION Warranty Information:
limited lifetime
THANK YOU